Powersoft Duecanali 1604-DSP-DANTE Förstärkare
1600W/2 kanals förstärkare med DSP och Dante™. Förmågan att enkelt implementera alla konfigurationer gör Duecanali-serien extremt flexibel. Powersofts legendariska effektivitet sparar värdefull energi och håller både driftskostnader och ”koldioxidavtryck” på ett minimum. Duecanali 1604 DSP + D är konstruerad för att arbeta med Lo-Z (från 2 Ω) och med 70V / 100V distribuerade linjer: alla blandade impedansutgångsbelastningar kan realiseras. En helt integrerad toppmodern DSP ger omfattande systemhanteringsfunktionalitet. Förutom ljudformnings- och limiterfunktioner i unik Powersoft-stil. DSP-hårdvaran och ArmoníaPlus-programvara uppfyller IEC 60849 kraven för utrymningslarm.
Kontakta en produktexpert om denna produkt
Förmågan att enkelt implementera alla konfigurationer gör Duecanali-serien extremt flexibel. Powersofts legendariska effektivitet sparar värdefull energi och håller både driftskostnader och ”koldioxidavtryck” på ett minimum.
Duecanali 1604 DSP + D är konstruerad för att arbeta med Lo-Z (från 2 Ω) och med 70V / 100V distribuerade linjer: alla blandade impedansutgångsbelastningar kan realiseras.
En helt integrerad toppmodern DSP ger omfattande systemhanteringsfunktionalitet. Förutom ljudformnings- och limiterfunktioner i unik Powersoft-stil. DSP-hårdvaran och ArmoníaPlus-programvara uppfyller IEC 60849 kraven för utrymningslarm.
MyPowersoft-tjänster finns tillgängliga för denna produkt
Power supply
Powersoft legendary universal switch-mode power supply up to 400VAC tolerant with Power Factor Correction
Patented output filter with ripple cancellation network
Low Inrush Limiting reduces AC inrush current, removing the need for expensive power sequencers
Detachable AC mains cable with IEC C19/22.2 (16A for EU, 20 A for USA) socket
Protections
Fully protected circuit design with:Ac protection: shut down power supply when AC mains voltage is outside the operating range
Clip limiter: prevents severely clipped waveforms from reaching loudspeakers, while still maintaining full peak power output
DC protection: protects against infrasonic signal at the outputs
VHF protections: protects the loudspeakers against non-audible, strong, non-musical high-frequency signals
Short circuit protection: protects the amplifier from short circuit or other stressful events for the output circuits with automatic protection reset
Long term limiter: protects the loudspeaker against steady long term RMS (non-audio) signals, by reducing maximum output
Thermal protection: output stages operating temperature up to 80 °C (176 °F)
Temperature controlled continuous variable speed fan, front to back airflow
Temperature forecast with LCD traced historical behavior
General
Fixed frequency switchmode output stage for high grade sound accuracy
Compact size - all models only 1 RU for reduced rack cost and space
Light weight - for easier racking and shipping: 7 kg (15.4 lbs)
Standard Phoenix connectors: analog audio outputs, aux supply, alarms and GPIO
Remotely switchable double input (main and aux) per channel
Loudspeaker system configuration
Direct drive either low impedance loads or 70V / 100V Hi-Z distributed lines
Switchable 35Hz / 70Hz high pass filter per channel
Mixed configuration with Lo-Z/Hi-Z systems possible
Bridged mode low impedance per channel pair
Alarms and GPI/O
NC/NO contacts per channel for alarm notifications
Remote ON/OFF switch
Remote VCA control per channel
Digital Signal Processing
TI C6000 DSP platform
AD/DA converter: dual 24bit @ 48 kHz Tandem® architecture
Input/output independent equalizers per channel providing PEQ, raised cosine, shelving IIR filters as well as custom output FIR filters
Delay up to 100 ms for time alignment
Active DampingControl™ for cable compensation
Peak, RMS voltage, RMS current, TruePower™ limiters
Remote Control & Monitoring
Via software:Control and diagnostics monitoring via ArmoníaPlus
Dedicated WebApp
Via Hardware:Attenuation (from 0dB to 26dB)
High-pass filters (35Hz, 70Hz)
Lo-Z/Hi-Z/70V/100V output selection
Adjustable gain (from 26dB to 35 dB)
| GENERAL | |||
| Output power per Channel | |||
| Output power per Channel | 1000 W @ 2 Ω | 800 W @ 4 Ω | 800 W @ 8 Ω |
| Bridge mode | 2000 W @ 4 Ω | 1600 W @ 8 Ω | |
| Max output voltage / current | |||
| Max unclipped output voltage@8 Ω | 115 Vpeak | ||
| Current | 45 Apeak | ||
| AC MAIN POWER | |||
| Power supply | Universal, regulated switch mode with PFC (Power Factor Correction) | ||
| Nominal power requirement | 100-240 V ±10%, 50-60 Hz | ||
| Operating voltage | 90 V – 264 V | ||
| Power consumption / current draw | |||
| Idle | 115 V: 23 W – 0.34 A | 230 V: 23.3 W – 0.21 A | |
| 1/8 of max output power @ 4 Ω | 115 V: 267 W – 2.5 A | 230 V: 274 W – 1.5 A | |
| THERMAL | |||
| Operating temperature range | 0° – 45° C – 32° – 113° F | ||
| Thermal dissipation* | |||
| Idle | 115 V: 78 BTU/h | 230 V: 79 BTU/h | |
| 1/8 of max output power @ 4 Ω | 115 V: 229 BTU/h | 230 V: 251 BTU/h | |
| SKU | Duecanali 1604 DSP+D |
|---|---|
| Vikt (kg) | 9.000000 |
| Enhet | Stk |
| EAN | PF00H462 |
| Tillverkare | Powersoft |
| Produktserie | Duecanali-serie |
| Impedans | 2 Ohm, 4 Ohm, 6 Ohm, 8 Ohm, 16 Ohm, 70 Volt, 100 Volt |
| Watt effekt | 1000w till 1999w |
| Kraftbehov | 230V |
| Power sharing | Ja |
| AoIP standard | Dante |
| Fläktlös | Nej |
Förmågan att enkelt implementera alla konfigurationer gör Duecanali-serien extremt flexibel. Powersofts legendariska effektivitet sparar värdefull energi och håller både driftskostnader och ”koldioxidavtryck” på ett minimum.
Duecanali 1604 DSP + D är konstruerad för att arbeta med Lo-Z (från 2 Ω) och med 70V / 100V distribuerade linjer: alla blandade impedansutgångsbelastningar kan realiseras.
En helt integrerad toppmodern DSP ger omfattande systemhanteringsfunktionalitet. Förutom ljudformnings- och limiterfunktioner i unik Powersoft-stil. DSP-hårdvaran och ArmoníaPlus-programvara uppfyller IEC 60849 kraven för utrymningslarm.
MyPowersoft-tjänster finns tillgängliga för denna produkt
Power supply
Powersoft legendary universal switch-mode power supply up to 400VAC tolerant with Power Factor Correction
Patented output filter with ripple cancellation network
Low Inrush Limiting reduces AC inrush current, removing the need for expensive power sequencers
Detachable AC mains cable with IEC C19/22.2 (16A for EU, 20 A for USA) socket
Protections
Fully protected circuit design with:Ac protection: shut down power supply when AC mains voltage is outside the operating range
Clip limiter: prevents severely clipped waveforms from reaching loudspeakers, while still maintaining full peak power output
DC protection: protects against infrasonic signal at the outputs
VHF protections: protects the loudspeakers against non-audible, strong, non-musical high-frequency signals
Short circuit protection: protects the amplifier from short circuit or other stressful events for the output circuits with automatic protection reset
Long term limiter: protects the loudspeaker against steady long term RMS (non-audio) signals, by reducing maximum output
Thermal protection: output stages operating temperature up to 80 °C (176 °F)
Temperature controlled continuous variable speed fan, front to back airflow
Temperature forecast with LCD traced historical behavior
General
Fixed frequency switchmode output stage for high grade sound accuracy
Compact size - all models only 1 RU for reduced rack cost and space
Light weight - for easier racking and shipping: 7 kg (15.4 lbs)
Standard Phoenix connectors: analog audio outputs, aux supply, alarms and GPIO
Remotely switchable double input (main and aux) per channel
Loudspeaker system configuration
Direct drive either low impedance loads or 70V / 100V Hi-Z distributed lines
Switchable 35Hz / 70Hz high pass filter per channel
Mixed configuration with Lo-Z/Hi-Z systems possible
Bridged mode low impedance per channel pair
Alarms and GPI/O
NC/NO contacts per channel for alarm notifications
Remote ON/OFF switch
Remote VCA control per channel
Digital Signal Processing
TI C6000 DSP platform
AD/DA converter: dual 24bit @ 48 kHz Tandem® architecture
Input/output independent equalizers per channel providing PEQ, raised cosine, shelving IIR filters as well as custom output FIR filters
Delay up to 100 ms for time alignment
Active DampingControl™ for cable compensation
Peak, RMS voltage, RMS current, TruePower™ limiters
Remote Control & Monitoring
Via software:Control and diagnostics monitoring via ArmoníaPlus
Dedicated WebApp
Via Hardware:Attenuation (from 0dB to 26dB)
High-pass filters (35Hz, 70Hz)
Lo-Z/Hi-Z/70V/100V output selection
Adjustable gain (from 26dB to 35 dB)
| GENERAL | |||
| Output power per Channel | |||
| Output power per Channel | 1000 W @ 2 Ω | 800 W @ 4 Ω | 800 W @ 8 Ω |
| Bridge mode | 2000 W @ 4 Ω | 1600 W @ 8 Ω | |
| Max output voltage / current | |||
| Max unclipped output voltage@8 Ω | 115 Vpeak | ||
| Current | 45 Apeak | ||
| AC MAIN POWER | |||
| Power supply | Universal, regulated switch mode with PFC (Power Factor Correction) | ||
| Nominal power requirement | 100-240 V ±10%, 50-60 Hz | ||
| Operating voltage | 90 V – 264 V | ||
| Power consumption / current draw | |||
| Idle | 115 V: 23 W – 0.34 A | 230 V: 23.3 W – 0.21 A | |
| 1/8 of max output power @ 4 Ω | 115 V: 267 W – 2.5 A | 230 V: 274 W – 1.5 A | |
| THERMAL | |||
| Operating temperature range | 0° – 45° C – 32° – 113° F | ||
| Thermal dissipation* | |||
| Idle | 115 V: 78 BTU/h | 230 V: 79 BTU/h | |
| 1/8 of max output power @ 4 Ω | 115 V: 229 BTU/h | 230 V: 251 BTU/h | |
| SKU | Duecanali 1604 DSP+D |
|---|---|
| Vikt (kg) | 9.000000 |
| Enhet | Stk |
| EAN | PF00H462 |
| Tillverkare | Powersoft |
| Produktserie | Duecanali-serie |
| Impedans | 2 Ohm, 4 Ohm, 6 Ohm, 8 Ohm, 16 Ohm, 70 Volt, 100 Volt |
| Watt effekt | 1000w till 1999w |
| Kraftbehov | 230V |
| Power sharing | Ja |
| AoIP standard | Dante |
| Fläktlös | Nej |
Validate your login
Logga in
Skapa nytt konto